Post has attachment
1 Ranking Company water Soluation .Etp Plant In bangladesh . ToptechBD

#EFFULENT
#TREATMENT
#PLANT
A Presentation By
Top Tech bd
NEED OF ETP
 Water is basic necessity of life used for many purposes
one of which is industrial use.
 Industries generally take water from rivers or lakes but
they have to pay heavy taxes for that.
 So its necessary for them to recycle that to reduce cost
and also conserve it.
 Considering these criteria an Effluent Treatment Plant is
also being established in Rourkela Steel Plant.
 Main function of this ETP is to clean GCP effluent and
recycle it for further use.
DESIGN PARAMETERS
Slurry Feed Characteristics
 Type of Slurry Gas Cleaning Plant of Blast Furnace.
 Flow Rate 1140 m3
/hr
 Suspended Matter 6000 ppm(Av of 4000-8000)
 pH 4.5 – 6.5
 Temperature 60-70oC.
Approx. particle size distribution
 < 10 micron: 30%
 10 to 40 micron: 35%
 40 to 60 micron: 15%
 >60 micron: 20%
Analysis of suspended solids
a.) Fe2O3……………….71.42%
b.) SiO2…………………5%
c.)Al2O3………………..0 .4%
d.) CaO………………… 6%
e.) MgO………………….3.2%
f.) P………………………0.016%
g.) S………………………0.483%
PROCESS DESCRIPTION
INLET LAUNDER
 The purpose of launder is to flow the effluent of
gas scrubber to distribution chamber
 Inlet channel is designed for a surge flow of
1950m3
/hr @ slope of 2% so water flows at
1.5m/s(self cleaning velocity).
 Self cleaning velocity is that velocity at which if
the sludge flows it will not get accumulated in
the launder.
DISTRIBUTION CHAMBER
 Purpose of distribution chamber is to divide the
flow (design flow of 1140m3
/hr) into two equal
flows.
 In case if one of the thickener is closed then there
would be no distribution so selection of pipes is
done on this criteria.
 The size of gates is designed such that there is
equal distribution always.
FLASH MIXER
 There are two flash mixers designed for a flow of
1140m3
/hr with a retention time of 60 sec.
 So its volume must lie around 19m3
.
 In flash mixer alum (coagulant) acts upon sludge
so that suspended solids settle down. In addition
pH of sludge is also raised by lime as it is
required to have a pH of 7-9. Polyelctrolytes
(flocculants) also act upon to fasten the process of
coagulation.
CHEMICAL ACTION OF ALUM AND LIME
 Al2 (SO4
)3
.12H 2 O 2Al3++ 3SO4
2- + 12H2O
 SO42-+H2O HSO4-+ OH-
(Cause pH change)
 Ca (OH) 2 Ca2+ + 2OH-
(Cause pH change)
 The basic water causes Al(OH) 3
to precipitate
bringing small particles with them and then
making water clear. Fe2O3
is removed mainly by
coagulation.
 The polyelectrolytes make big lumps of the
coagulated particles so they settle down.
CLARIFIER
 The clarifier separates the treated slurry from
clean water.
 The sludge settles down and clean water at the
top flows down to the cooling tower from where it
is cooled and recycled. According to PG the SS
content in this water must not be greater than
100 ppm.
 The clarifier has a racker arm which extracts the
sludge out of clarifier. In case if sludge height
goes higher than the racker arm then it will
automatically lift up and then settle down taking
sludge with it.
 From here sludge is pumped to sludge tank.
A GENERAL STRUCTURE OF CLARIFIER
Sludge tank
 In the sludge tank the sludge is continuously
agitated in order to prevent settlement of sludge.
 Each tank has capacity of 224m3 and can hold for
8 hrs.
 Main purpose of the tank is to hold sludge for
transfer to filter press.
 From sludge tank the sludge is pumped to filter
press by filter press feed pump.
Filter press
 Sludge from the sludge tank will be pumped to the Filter
Press equipments for dewatering purpose. According to
performance guarantee the cake moisture should not be
more than 20%.
 For this purpose different types of filters are used namelygravity
setters, gravity belt filters, centrifuges, vacuum or
pressure belt filters and filter press. But among these filter
press is most efficient and economical.
 Other filtration systems offer high pressure filtration, but
only the filter press has both high pressure capability
and efficient filter cake removal. The filter elements
are constructed of lightweight polypropylene. They are
extremely corrosion resistant and virtually eliminate plate
breakage.
RECESSED PLATE FILTER PRESS
WORKING
 Dewatering is accomplished by pumping a slurry
or sludge into chambers (A) surrounded by filter
membranes (B).
 As pumping pressure is increased the filtrate is
forced through the accumulated filter cake (C)
and membrane until the chamber is full of solid
filter cake. The chambers are formed by two
recessed plates held together under hydraulic
pressure.
 The hydraulic ram (D) moves the follower (E)
against the stack of filter plates (F) closing the
press. The ram continues to apply sealing
pressure of sufficient force to counteract the high
internal compaction pressures.
 The head stock (G) and tail stock (H) are held in
place by specially engineered side rail support bars
(I). The filtrate passes through the membrane and
is directed by channels in the plates and drain ports
(J) to the head stock for discharge.
 The filtrate typically contains less than 15 PPM
suspended solids. The filter cake is easily removed
by simply reversing the hydraulic ram, thus
opening the press. The lightweight plates may then
be moved apart, permitting the compacted cake to
fall from the chambers.
 Higher the internal pressure, the greater the solids
compaction. The standard press is constructed to
withstand 100 PSI compaction pressure producing
a hard dry cake. The special high pressure press
can withstand 225 PSI for sludge more difficult to
dewater.
THANK
YOU

Photo

Post has attachment

Post has attachment

Post has attachment

Post has attachment

Post has attachment

Post has attachment

Post has attachment

Wait while more posts are being loaded