Flying robots!
See all
Members (27,559)
Sonal Chokshi's profile photo
Gary Mortimer's profile photo
Chris Anderson's profile photo
Yaich Mahdi's profile photo
Guadalupe Guerrero's profile photo
Nanjunda Pratap Palecanda's profile photo
WesLee Frisby's profile photo
Ray Jacobs's profile photo
jonathan rocha's profile photo
Oubedan Tardy's profile photo
Dean Ervik's profile photo
Mehrzad Karami's profile photo
Sanket Gajjar's profile photo
Budapest DroneStore's profile photo
Sonja Peterson's profile photo
이상훈's profile photo
Keith Hankins's profile photo
hassel k's profile photo
Egidijus Blaževičius's profile photo
GorBua Jacky's profile photo
ModZilla The Mercilous's profile photo
idris yeniçeri's profile photo
stefano piantoni's profile photo
maxim nikishin's profile photo

Stream

Join this community to post or comment
 
 
Built a prototype cargo box for my H. Tested it today, and it flew perfectly. Wind hits it pretty hard on the sides but forward flight is not effected at all. All in all I would rate the flight 7/10. It's a good design. I lifted a light load today, just my cell phone, but I plan on putting heavier loads in it in the future.
2
Add a comment...

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+
 ·  Translate
1
Add a comment...

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+
 ·  Translate
1
Add a comment...

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+
 ·  Translate
1
Add a comment...

Robert Moore

Discussion  - 
2
1
Jun Yamog's profile photo
4 comments
 
I built something similar 2 years ago. Some info on my blog. Right now I used small PDB that came from Hobby King micro APM. http://jkyamog.blogspot.co.nz/search/label/v550
Add a comment...

Nate Taylor

Discussion  - 
 
This is as far as I am getting until I get my KISS FC. Will do some more cleaning up then. No cam yet, waiting for the FC on that also. It's mounted, just not wired.
6
1
Nate Taylor's profile photo
2 comments
 
Lmao! This thing is drunk in horizon mode. Acro seems okay. Not sure how important horizon is to me any way, but playing with the pid's might be good practice.
Add a comment...

Fdrs sas

Discussion  - 
1
Add a comment...

Thomas Herrmann

Discussion  - 
 
For those interested in the use of UAVs in agriculture: RUCON has released there finalized version of a 100% reliable trichogramma dispenser. Including software for validation. 
5
2
Thomas Herrmann's profile photo
2 comments
 
Oh sorry, it translates to european corn borer. It is a way of biological treatment of corn insects. Pretty popular already :) http://biocare.de/language/en/

Add a comment...

DRONES RD

Discussion  - 
 
Hola a todos, quien me puede apoyar suscribiendose a mi canal de youtube.

Muchas informaciones sobre Drones de carreras.

https://www.youtube.com/watch?v=pqTYK6YZUIA
 ·  Translate
1
Add a comment...

About this community

All about amateur Unmanned Aerial Vehicles (UAVs) and their many non-military uses. The G+ home of the DIY Drones community (diydrones.com) and those interested in personal/DIY robotics.

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+

 ·  Translate
1
Add a comment...

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+
 ·  Translate
1
Add a comment...

Davide Sottili

Discussion  - 
 
New video
CX-20 + GOPRO HERO 3+
 
New video
Cx-20 + GOPRO HERO 3+
 ·  Translate
1
Add a comment...

Thomas Jernberg

Discussion  - 
 
Nice little roadtrip in Sweden with good friends, lincoln and Diy X525 v3
https://youtu.be/V271owL1xLw
1
Add a comment...

Nate Taylor

Discussion  - 
 
I may have neglected to use loctite.
All in all today was a successful first day as a pilot. Used up 1 battery on tuning, and 1 flying around and trying some acrobatics. I got the backflip down pretty good. Video of that once I get from my buddy.
Oh, and no actual broken parts or props. Woohoo!
5
1
Nate Taylor's profile photo
2 comments
 
+Blake Hardison​ Unfortunatly I can still do a good bit of tunning. I still have a little bit of wobble on yaw. I need to play with my throttle on my tx some more also. Honestly, I think I got pretty lucky with where tuning is so far.
The motors are kingkong 2205 2300kv. Just some cheapo's that are alright. I managed to knock a magnet out of socket on one. Had to disasemble the motor to get it back in place. Not sure if that eas build quality or my several hard knocks. It seems to free spin properly again. Gonna test it on my lunch.

Oh, worth noting. I am only running 4045 props. Got them on accident.
Add a comment...

Nate Taylor

Discussion  - 
 
This is about as far as I will get for tonight. All my ESC's are secure. One slipped a little, so I shot some extra hot glue on it. It's still on a kilt, but it isn't moving.
Got the motors mounted and started wiring and quickly realized I had one of my CC motors backwards. Gave up for the night, but damn I am getting excited. All's good and so so close.

8
Nate Taylor's profile photoBlake Hardison's profile photo
13 comments
 
Lol np. The build is where I spend 99% of my time
Add a comment...

Nate Taylor

Discussion  - 
 
 
Got my littlebee esc's today. I got the motor leads soldered on and trying to figuring out placement. I am hell bent on tucking these little guys between my spacer. I am just not a fan of that huge hole in the center of the bottom plate. Doesn't leave a lot of surface for sticky tape.
Any ideas on how to secure these? I could zip tie them, however what you see of the esc is about it. I have way to much heat shrink on.
3
Nate Taylor's profile photoMuhammad Abdul Hadi's profile photo
13 comments
 
5.8 bro, it's the latest FX798T
Add a comment...

Alex Xo

Discussion  - 
 
RC Yak-130 at RusJet 2016
Subscribe!
8
Add a comment...