Post has attachment
http://silipump.com/marine-pump/clh-pump
CLH vertical centrifugal marine pump

The SILI CLH pump is an ideal centrifugal marine pump. CLH vertical marine pump is popularly used in marine and offshore industry. It is a centrifugal type with volute casing vertical construction. And it is single stage, single flow. CLH pump is suitable liquid for fresh water or sea water with little particle below 70 C degree. Specially mechanical seal for 120 C degree is available. CLH pump typical spplication is for fresh and seawater cooling pumps; bilge and ballast pumps, fire-fighting, general service pumps, deck-wash pumps and so on. CLH pump spare parts can be also available in our sides.

The CLH marine centrifugal pump Feather:
a. Curved blades to ensure low NPSH-values and high efficiency impeller, it is close type, statically and dynamically balanced .
b. Shaft supported by radial and thrust ball bearings either grease or self-lubricated.
c. High quality replaceable mechanical shaft seal of an approved brand; it is carbon/ceramics/stainless steel material. A special mechanical seal for temperature higher than 120 C.
d. Bronze pump casing&body, impellers and stainless steel shaft as standard for sea water.
e. Flanges are usually in Chinese GB standard. However other standard flanges in EN(DIN), ANSI, and JIS and so on, can be also provided.
f. A priming air ejector can be equipped on sides pump.
Refer to pump and its spare parts details from the CLH pump catalogue. Contact us more information for pump specification, manual, performance curve, installation dimension, spare parts list and so on.

The CLH pump, in spacer coupling type and monoblock(direct) type design. The pumps are available in sizes ranging from 25 mm to 250 mm on the suction flange. The suction flange is bigger than the discharge flange in 2 poles motor pump; or it is same with the discharge flange in 4 poles motor pump.
The CLH pump is a single stage, single suction centrifugal pump used in marine and off shore industry. The pump is a so-called in-line type, i.e. suction and pressure branches are mounted on the centre line.
Shaft and shaft seal: basically there are two kinds of shaft sealing: the packing and the mechanical seal, a mechanical shaft seal with stainless steel shaft is a standard.
Bearings: the pump shaft is guided by antifriction bearings. It is usually designed for grease lubrication(standard) or oil lubrication.
Material for wet part: pump impeller, pump cover & casing(body) are in brozne for standard for sea water; while for fresh water, cast iron pump casing is optional
Motor: in high class and insulation level, TEFC, IEC standard, 50Hz or 60Hz; especially designed for marine and off shore purpose.
Refer to more from link:
http://silipump.com/marine-pump/clh-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/clhb-pump
CLHB vertical centrifugal marine pump

The SILI CLHB pump is an ideal centrifugal marine pump type, which is popularly used in marine and offshore industry. It is can be in spacer coupling type. It is a centrifugal type with volute casing, vertical construction, single stage, single flow, in line and same flanges. CLHB pump is suitable liquid for fresh water or sea water with little particle below 70 C degree, (specially mechanical seal for 120 C degree). CLHB pump application for fresh and seawater cooling pumps, bilge and ballast pumps, fire-fighting, general service pumps, deck-wash pumps and so on. CLHB pump spare parts can be also available in our sides.

CLHB vertical centrifugal marine pump Feather:
a. Curved blades to ensure low NPSH-values and high efficiency, close type, statically and dynamically auto balanced.
b. Shaft supported by radial and thrust ball bearings either greases or self-lubricated, independent bearing body and pump shaft support.
c. High quality replaceable mechanical shaft seal of an approved brand, tungsten carbon/ceramics, A special mechanical seal for temperature higher than 120 C.
d. Bronze pump casing&body, impellers and stainless steel shaft as standard for sea water.
e. Flanges are usually in Chinese GB standard, however other standard flanges in EN(DIN), ANSI, and JIS and so on, can be also provided.
f. Coupled to 2 or 4 pole quality IEC motor configurations, with high level class and insulation, in both 50Hz and 60Hz, suitable for marine purpose.
e. Spacer coupling type, available, when replacing both mechanical seal and impeller, it only needs to remove the elastic clutch and the nut on the lid and, without removing the motor, pump casing and pipeline(for the spacer coupling type only)
Refer to pump and its spare parts details from the CLHB pump catalogue, and contact us more information for pump specification, manual, performance curve, installation dimension, spare parts list and so on.

The CLHB pump, in spacer coupling type design. The pumps are available in sizes ranging from 25 mm to 250 mm on the inlet and outlet flange.The suction flange is same with the discharge flange.
The CLHB pump is a single stage, single suction centrifugal pump used in marine and off shore industry. The pump is a so-called in-line type, i.e. suction and pressure branches are mounted on the centre line.
Shaft and shaft seal: basically there are two kinds of shaft sealing: the packing and the mechanical seal, a mechanical shaft seal with stainless steel shaft is a standard.
Bearings: the pump shaft is guided by antifriction bearings. It is usually designed for grease lubrication(standard) or oil lubrication.
Material for wet part: pump impeller, pump cover & casing(body) are in brozne for standard for sea water, while for fresh water, cast iron pump casing is optional.
Motor: in high class and insulation level, TEFC, IEC standard, 50Hz or 60Hz, especially designed for marine and off shore purpose.
Refer to more from link:
http://silipump.com/marine-pump/clhb-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/cisg-pump
CISG vertical closed coupling centrifugal marine pump

The SILI CISG pump is a popular centrifugal marine pump, which is widely used in marine and offshore industry. This pump performance is on the basis of CIS pump, but just in vertical type. CISG pump is a centrifugal type with single stage, single flow, in line and same flanges. it is suitable liquid for fresh water or sea water with little particle below 70 C degree, (specially mechanical seal for 120 C degree). CISG pump application for fresh and seawater cooling pumps, bilge and ballast pumps, fire-fighting, general service pumps, deck-wash pumps and so on. CISG pump spare parts can be also available in our sides.

CISG vertical centrifugal marine pump Feather:
a. Mono-block design type, it request much less space for pump installation, which the operation is more convenient.
b. High quality replaceable mechanical shaft seal of an approved brand, tungsten, carbon, ceramics, stainless steel material. A special mechanical seal for temperature higher than 120 C.
c. Bronze pump casing&body, impellers and stainless steel shaft as standard for sea water.
d. Coupled to 2 or 4 pole quality IEC motor configurations, with high level class and insulation, in both 50Hz and 60Hz, suitable for marine purpose.
e. Pump inlet and outlet flange is inline and same. Pump can be installed like a valve in the pipeline.
f. The lower barycenter of the vertical structure which coincides with the center of the pump feet strengthens the stability of running and the duration.
Refer to pump and spare parts details from the CISG pump catalogue, and contact us more information for pump specification, manual, performance curve, installation dimension, spare parts list and so on.
The CISG pump, in mono-block type design. The pumps are available in sizes ranging from 25 mm to 100 mm on the inlet/outlet flange. The suction flange is same with the discharge flange.

The CISG pump is a single stage, single suction centrifugal pump used in marine and off shore industry. The pump is a so-called “in-line” type, i.e. suction and pressure branches are mounted on the centre line.
Shaft and shaft seal: basically there are two kinds of shaft sealing: the packing and the mechanical seal, a mechanical shaft seal with stainless steel shaft is a standard.
Bearings: the pump shaft is guided by antifriction bearings. It is usually designed for grease lubrication(standard) or oil lubrication.
Material for wet part: pump impeller, pump cover & casing(body) are in bronze for standard for sea water, while for fresh water, cast iron pump casing is optional
Motor: in high class and insulation level, TEFC, IEC standard, 50Hz or 60Hz, especially designed for marine and off shore purpose.
Refer to more from link:
http://silipump.com/marine-pump/cisg-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/gdl-pump
GDL multistage centrifugal marine boiler pump

The SILI GDL pump is a multistage, single suction, vertical(inline) centrifugal marine pump. This pump has high pump head in small capacity, so it is especially suitable for the marine boiler feed water pump on board vessels or offshore platform.
Applications: The SILI GDL pump is especially designed for the marine boiler feed water pump, condensate pump and boiler circulation water pump in the marine and offshore industry. It can be also worked as the booster pump, jockey pump fire-fighting pump, deck wash pump and so on.
GDL multistage centrifugal marine pump Design Features:
a. Designed in inline structure, pump can be installed like a valve in the pipeline system.
b. Multistage type, in a vertical sectional impeller, which result a compact installation space. The tightening bolt and nut hold these sections together.
c. High quality mechanical seals(carbon/ceramic/stainless steel).(Gland packing is available), max temp to 120C degree in high pressure type.
d. A bearing bush and shaft sleeve are equipped insides the pump, and lubricated by the grease.
e. Stainless steel pump casing, body, impellers, and also stainless steel shaft as standard.
f. Coupled to 2 pole quality IEC motor configurations, with high level class and insulation, in both 50Hz or 60Hz, suitable for marine purpose.
refer to more GDL pump information from the link:
http://silipump.com/marine-pump/gdl-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/emc-pump
EMC Taiko vertical centrifugal pump

EMC Pump APPLICATION: Cooling Fresh Water Cooling Sea Water Sea Water Service Ballast
CONSTRUCTION: Vertical inline, single stage, single suction. Closed coupling type.
The EMC vertcial centrifugal marine pump is solid casing type and is fitted to motor shaft rigidly. This series can be used for Line pump because the center of gravity and height is low and suction inlet and discharge out let of the both sides are in a straight line. The pump can be used as an automatic self-priming pump by fitting an air ejector.
It has same design and size with Taiko EMC pump, EMC pump spare parts can be also available in our sides.
Refer to more pump and its spare parts details from the EMC pump link:
http://silipump.com/marine-pump/emc-pump
Add a comment...

Post has attachment
http://silipump.com/marine-pump/esc-pump
ESC Taiko vertical centrifugal pump

ESC Pump APPLICATION: Cooling Fresh Water Cooling Sea Water Sea Water Service bilge & Ballast Ballast, Fire & General Service
CONSTRUCTION: Vertical inline, single stage, single suction. Spacer coupling type.
The ESC centrifugal marine pump is solid casing with spacer coupling, the pump can be disassembled or inspected without removing the motor. There is neither load to the motor bearing nor problem in case of the dry-operation because the pump shaft has an independent bearing. The ESC-type can be used as an automatic self-priming pump by fitting an air ejector.
ESC pump is in same desgin and size with Taiko pump. ESC pump spare parts can be also available in our sides.
Refer to more pump and its spare parts details from the ESC pump link:
http://silipump.com/marine-pump/esc-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/emd-pump
EMD Taiko vertical centrifugal pump

EMD Pump APPLICATION: Cooling Fresh Cooling Sea Water Sea Water Service Bilge & Ballast Ballast, Fire &General Service
CONSTRUCTION: Vertical inline, single stage, double suction. Closed coupling type.
EMD vertical double suction centrifugal marine pump is solid casing type and is fitted to motor shaft rigidity. This series can be used for Linepump because the center of gravity and height is low and suction inlet and discharge out let of the both sides are in a straight line. The pump can be used as an automatic self-priming pump by fitting an air ejector.
EMD pump is same in design and size with Taiko pump. EMD pump spare parts can be also available in our sides.
Refer to more pump and its spare parts details from the EMD pump link:
http://silipump.com/marine-pump/emd-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/esd-pump
ESD Taiko vertical centfifugal pump

ESD Pump APPLICATION: Cooling Fresh water Cooling Seawater Sea Water Service Bilge & Ballast, Ballast, Fire &General Service
CONSTRUCTION: Vertical inline, single stage, double suction. Spacer coupling type.
The ESD vertcial double suction centrifugal marine pump is solid casing with spacer coupling, the pump can be disassembled or inspected without removing the motor. There is neither load to the motor bearing nor problem in case of the dry operation because the pump shaft has an independent bearing. The pump can be used as an automatic self-priming pump by fitting an air ejector.
ESD pump is in same desgin and size with Taiko pump. ESD pump spare parts can be also available in our sides.
Refer to more pump and its spare parts details from the ESD pump link:
http://silipump.com/marine-pump/esd-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/cis-pump
CIS end-suction centrifugal marine pump

The SILI CIS pump is a single stage, single suction, end-suction centrifugal marine pump. The CIS pump is designed according to international standard. ISO2858. It is for the end-suction centrifugal pump about the designation, nominal duty point and dimensions. The CIS horizontal centrifugal marine pump is suitable liquid for fresh water or sea water with little particle below 70 C degree. Specially mechanical seal for 120 C degree is available. CIS pump application for cooling pumps and fresh water booster or circulation pumps. In addition, bilge and ballast pumps, fire-fighting, general service pumps, Deck-wash pumps and so on. CIS pump spare parts can be also available in our sides.

CIS horizontal centrifugal marine pump Feather:
a. Designed to comply with ISO 2858 standard.
b. Back pull-out design. The bolting to the base plate through the casing feet together with spacer coupling; allow an easy disassembly of the rotating parts without disturbing the alignment and without disconnecting pipes and motor.
c. High quality mechanical seals(carbon/ceramic/stainless steel) with balanced configuration. Most of the pumps are designed with sealing rings at the front and back of impellers.(Gland packing is available).
d. Two bearing housings fitted with deep groove rolling ball bearings. Pumps are fitted with greased for life bearings, or bearings are oil bath lubricated.
e. Bronze pump casing&body, impellers and stainless steel shaft as standard for sea water.
f. Bare shaft and frame mounted for direct coupling to electric motors, coupled to 2 or 4 pole quality IEC motor configurations. It is with high level class and insulation, in both 50Hz or 60Hz, suitable for marine purpose.
Refer to pump and its spare parts details from the CIS pump catalogue. And contact us more information for pump specification, manual, performance curve, installation dimension, spare parts list and so on.

The CIS pump is available in sizes ranging from 50 mm to 200 mm on the suction flange. The suction flange is bigger than the discharge flange.
The CIS pump is are single-stage volute casing pumps used in marine and off shore industry. Hydraulic design and dimensions comply with ISO 2858. The pump is a so-called “End-suction” type, i.e. suction and pressure branches are mounted on vertical line.
Shaft and shaft seal: basically there are two kinds of shaft sealing: the packing and the mechanical seal, a mechanical shaft seal with stainless steel shaft is a standard.
Bearings: the pump shaft is guided by antifriction bearings. It is usually designed for grease lubrication or oil lubrication.
Material for wet part: pump impeller, pump cover & casing(body) are in brozne for standard for sea water, while for fresh water, cast iron pump casing is optional
Motor: in high class and insulation level, TEFC, IEC standard, 50Hz or 60Hz, especially designed for marine and off shore purpose.
Refer to more from link:
http://silipump.com/marine-pump/cis-pump/
Add a comment...

Post has attachment
http://silipump.com/marine-pump/cwz-pump
CWZ self-priming centrifugal marine pump

The SILI CWZ pump is a single stage, single suction, end-suction centrifugal marine pump. It is especially with built-in self-priming device. (No need for extra water ring or air ejector vacuum pump). CWZ pump is suitable liquid for fresh water or sea water with little particle below 70 C degree; specially mechanical seal for 120 C degree.
CWZ horizontal self-priming centrifugal marine pump application for fire-fighting pump, bilge pump, ballast pump, G/S(general service pump), and also cooling pump. With its built-in self-priming device, it is very suitable for the emergency condition purpose, there is no need extra self-priming pump, so the CWZ pump save space and make easy operation and maintenance. CWZ pump spare parts can be also available in our sides.

CWZ self-priming centriufgal marine pump Feather:
a. Self-priming design, with a no-return valve at the suction sides, avoid return of water when pump stopping.
b. Two bearing housings fitted with deep groove rolling ball bearings. Pumps are fitted with greased for life bearings, or bearings are oil bath lubricated.
c. High quality mechanical seals(carbon/ceramic/stainless steel), most of the pumps are designed with sealing rings at the front and back of impellers.
d. Bronze pump casing&body, impellers and stainless steel shaft as standard for sea water.
e. Flanges are usually in Chinese GB standard, however other standard flanges in EN(DIN), ANSI, and JIS and so on, can be also provided.
Refer to more pump and its spare parts details from the CWZ pump catalogue, and contact us more information for pump specification, manual, performance curve, installation dimension, spare parts list and so on.

The CWZ pump is available in sizes ranging from 32 mm to 100 mm on the suction flange. The suction flange and the discharge flange are in same size.
The CWZ pump is are self-priming single-stage, single suction centrifugal pumps used in marine and off shore industry. This pump has a built-in self-priming device, therefore, no need extra self-priming, such as water ring vaccum pump or air ejector pump. The pump is a so-called “End-suction” type, i.e. suction and pressure branches are mounted on vertical line.
Shaft and shaft seal: basically there are two kinds of shaft sealing: the packing and the mechanical seal, a mechanical shaft seal with stainless steel shaft is a standard.
Bearings: the pump shaft is guided by two rolling bearings. It is usually designed for grease lubrication or oil lubrication.
Material for wet part: pump impeller, pump cover & casing(body) are in brozne for standard for sea water, while for fresh water, cast iron pump casing is optional
Motor: in high class and insulation level, TEFC, IEC standard, 50Hz or 60Hz, especially designed for marine and off shore purpose.
Refer more from the link:
http://silipump.com/marine-pump/cwz-pump/
Add a comment...
Wait while more posts are being loaded