Profile cover photo
Profile photo
Ventor Technologies
6 followers -
An Embedded Systems online shop and design house
An Embedded Systems online shop and design house

6 followers
About
Posts

Post has shared content
TDA7297 Based Audio Amplifier board, This board runs on 12V DC supply voltage and produces 15W per channel output on 4-8 ohm speaker. this is a stereo output board. This Board requires soldering to complete, package includes PCB and spare parts to make this DIY board.
Add a comment...

Post has attachment
TDA7297 Based Audio Amplifier board, This board runs on 12V DC supply voltage and produces 15W per channel output on 4-8 ohm speaker. this is a stereo output board. This Board requires soldering to complete, package includes PCB and spare parts to make this DIY board.
Add a comment...

Post has attachment
A4988 is a micro-stepping motor driver with built-in translator for easy operation. A4988 module supports full, half, 1/4, 1/8 and 1/16 step modes, output drive capacity of up to 35V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one micro step. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened.
Add a comment...

Post has attachment
These are Banana Terminal socket for connecting single wire. This Banana socket is good for 15A, 250V AC or DC connection. BTI-15 model is 4MM size for banana plug, and maintain International quality standard. This is a pack of 4 Pcs and four color sockets.
Add a comment...

Post has attachment
AT90USB162 is a high-performance, low-power Atmel 8-bit AVR RISC-based microcontroller wit inbuilt USB controller and combines 16KB ISP flash memory with read-while-write capabilities, 512B EEPROM, 512 bytes SRAM, 22 general purpose I/O lines, 32 general purpose working registers, two flexible timer/counters with compare modes and PWM, USART, programmable watchdog timer with internal oscillator, SPI serial port, debug WIRE interface for on-chip debugging and programming, and five software selectable power saving modes. The device operates between 2.7-5.5 volts.
Add a comment...

Post has attachment
The MAX30100 is an integrated pulse oximeter and heart-rate monitor sensor solution. It combines two LEDs, a photo detector, optimized optics, and low-noise analog signal processing to detect pulse oximetry and heart-rate signals.The MAX30100 operates from 1.8V and 3.3V power supplies and can be powered down through software with negligible standby current, permitting the power supply to remain connected at all times. Onboard 3.3V LDO support 5V at VIN pin.
Add a comment...

Post has attachment
This is a Max7219 driven 8x8 dot matrix led module. Total 64 dots are controlled by row and segment. This module is serially driven by any microcontroller or Arduino using only 3 lines. This operates at 5V DC. LED produces Bright Red dots. More than One module can be used by cascading them for large display boards. Suitable for advertisements or any type of message display. This MAX7219 Dot matrix LED display module supported by Parola Library as Generic Hardware.
Add a comment...

Post has attachment
Optical Fingerprint reader Sensor Module. Uses serial communication with microcontroller 3.3V or 5V lavel.
Add a comment...

Post has attachment
The STM32F030F4P6 board is a high-speed embedded development board which offers very great performance at less power consumption. When in running mode, maximum power consumption is 22 mA, and 175 uA. This board features 5.5 V to 3.3 V regulator, RESET button, onboard LED for power indication, jumper BOOT option, output pins and mounted pinhead specifically for ISP connection or SWD. This board also integrates micro USB power supply interface and ISP/SWD programming/debugging interface. These features make it ideal for a wide range of applications which need a relatively high processing power and more communication capabilities.
Add a comment...

Post has attachment
The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
Add a comment...
Wait while more posts are being loaded