Profile cover photo
Profile photo
SHANGHAI SPECIAL METAL SHANGHAI SPECIAL METAL
1 follower
1 follower
About
Posts

Post has attachment
Cinder Ladle
Cinder ladle is a load-bearing device whose sole purpose is to collect molten or solid slag generated during metallurgical or chemical processes, to retain it during transport and to deposit it at a place of disposal.
Material
We CSM cinder ladles are made from Cast Steel, which is similar to our ladles, we will offer the material specification as you required.
Design
Cinder ladles are crucial items as they are part of lifting equipment and therefore undergo in terms of mechanical design engineering and handling the national safety regulations of the state where they are supposed to be operated. Thus, the following design criteria must be taken into consideration:
Type of furnace that the slag pot will service,
Quantity and type of slag generated,
Method of handling and dumping the pot,
Heat impact during operation,
Dimensional restrictions,
Pot maintenance procedures
Cinder ladles designed by CSM comply with the requirements of structure dimensions, mechanical properties and guarantee by chemical composition, heat treatment, non-destructive testing and visual inspection against surface.
Photo
Add a comment...

Post has attachment
Ball mill feed inlet, feed outlet
Shanghai Special Metal Co., Ltd supplies ball mill head, feed inlet and feed outlet, . The materials of mill head are normally selected low carbon steel and low alloy steel. It's produced by casting, used in ball grinding mill, including the feed end and outlet end, our head/cap for the bellow ball grinding mill.
PhotoPhotoPhoto
7/14/16
3 Photos - View album
Add a comment...

Post has attachment
Grinding roller for vertical mill

Weight: 20-120T
Applicable devices: vertical mills, mineral slag vertical mills, cement vertical mills, steel slag vertical mills, nickel slag mills, raw material vertical mills and coal vertical mills.
Application: Cement, building material, chemical, coal and others
Customizable: Yes

Product Introduction
Grinding roller is a core part of vertical mill. Shanghai Special Metal Co., Ltd supplies customized service according to customers’ requirements. Besides, Shanghai Special Metal Co., Ltd obtains good reputations on grinding roller casting, finish machining and bead welding service.
Photo
Add a comment...

Post has attachment
We CSM ladles are made from Cast Steel, which is similar to the following standards, we will offer the material specification as you required.
Cast Steel material for Casting Ladles:BS 3100:1991 425-A2, ASTM A 27 60-30, DIN 17182 GS-16Mn5, JIS G7821:2000 SC42, ISO 3755:1991 230-450
PhotoPhotoPhoto
2016-07-01
3 Photos - View album
Add a comment...

Post has attachment
Shanghai Special Metal Co., Ltd can offer The steel claw/ yokes for the aluminum electrolyzer.
Electrolytic aluminum anode steel claw/yoke is also called electrolysis claw/yoke. There are several types of claws, such as parallel three claws, four claws, stereoscopic four claws, six claws, eight claws, double anode steel claw etc. The steel claw is connected to the copper bar to consist of Anode.
Photo
Add a comment...

Post has attachment
Weldings
We are a professional manufacturer and supplier focusing on welding, machining and fabrication. We develop and supply mining machine with ourselves intellectual property, they are widely applied in many Chinese industry. We produce the fittings for harbor machinery of QCC and gantry crane, such as running mechanism (also called crane bogie), lifting mechanism, jib lubbing mechanism, for shield boring machine, for blender, for water conservancy facilities, machining for mining machinery and metallurgical machinery.
Our capacity of welding has manual welding, PMIG, SAW welding and TIG, 150mm reeling machine. We have ability to supply many kinds of welding frame, structure girder, cylindrical barrel, box type structure, working platform, machinery foundations and austenite welding.
We have vertical lathe with 8 meters tactical diameter, and there will be a new vertical lathe with 12 meters, capable of machining super large frame member.
PhotoPhotoPhotoPhoto
2016-06-22
4 Photos - View album
Add a comment...

Post has attachment
Cast iron pump casing and pump cover
The pump casing we offer can meet the followings:
1. Tolerance size of the casting shall conform to ISO8026-3 DCTG 13-RMA 6(RMAG H)-GCTG 7-DS
2. Cracks, burnt, sand and slag inclusions are not allowed. On the unhandled surfaces should not be defects reducing the strength, performance and degrade casting presentation. Allowed correction of welding, in which defective cutting may be performed by the manufacturer's instruction. Locations of these defects in the casting and the butchering size under welding must be registered and entered in the casting documents. After removal of butchering defects, the surface should be grinded and monitored for completeness remove defects by dye penetration
3. Carry out UT of the castings: the end surfaces along the entire length in the area of the flange connector of the pump housing and cover (zone 1) in the area of the suction flange connector (zone2),in the area of the discharge flange connector (zone3), permitted without correcting defects of the equivalent size to 5mm not more than 3pcs.
4. The conformity checking with the chemical composition of the steels should be carried out from the each melt.
PhotoPhotoPhotoPhoto
2016-06-22
4 Photos - View album
Add a comment...

Post has attachment
Square Ingot Mould
Ingot mold is the necessary equipment for steel plant and repeatedly used for casting large amount of ingot, which has a big effect on the quality and the cost of ingot. The service time or ingot expend is one of the primary technology economic indicators.
From the view of vertical section, there are two kinds of square ingot mold. One is with hot-top or firewall, bigger upper and smaller lower. The other one is bottleneck with smaller lower and bigger upper. The former one is used to pour killed steel and is customarily called killed steel ingot mold and is also used to pour boiling steel. The latter one is traditionally used to pour boiling steel, customarily called boiling steel ingot mold, now is also widely used to pour killed steel. From the view of lumen cross section, the square ingot mold can be square, rectangle, round, polygon and so on. From the view of inside surface shape, square ingot mold can be convex side, concave side, straight shape, corrugated side and so on.
PhotoPhotoPhoto
2016-06-22
3 Photos - View album
Add a comment...

Post has attachment
Slab Ingot Mould
Slab Ingot mould is a modified new utility product, the feature of which is to install a curved mold cover with two or more conical exhaust ports at the corresponding driving fit on the die body top of the primary product. When the red-hot liquid steel poured into die body, the hot up-flow forces the normal temperature air out of the die body from exhaust ports. When liquid steel enters into curved mold cover, the hot airflow is preheated, warmed rapidly and does heat accumulation at mold cover.
Slab ingot mold is a modified new utility product, the feature of which is to install a curved mold cover with two or more conical exhaust ports at the corresponding driving fit on the die body top of the ingot slab mould. When the red-hot liquid steel is poured into die body, the hot up-flow forces the normal temperature air out of the die body from exhaust ports. When liquid steel enters into curved mold cover, the hot airflow is preheated, warmed rapidly and does heat accumulation at mold cover . When liquid steel enters into conical exhaust ports, the free slag precipitated from liquid steel spread flatly at the upper exhaust ports to keep warm.
Therefore, it is an available way of replacing the function of hanging casting power and insulation board, adding heat generating agent, which lowers cost and avoids dust pollution caused by casting power and adding heat generating agent, what’s more, which makes liquid steel in mold cover fill up the shrinkage space to reduce the ingot shrinkage. The product is utility and new with simple structure. It is safe and reliable to produce high quality billet.
Photo
Add a comment...

Post has attachment
Round ingot mold
Ingot mold is the necessary equipment for steel plant and repeatedly used for casting large amount of ingot, which has a big effect on the quality and the cost of ingot. The service time or ingot expend is one of the primary technology economic indicators.
Round ingot mold is the necessary equipment for steel plant and repeatedly used for casting large amount of ingot, which has a big effect on the quality and the cost of ingot. The service time or ingot expend is one of the primary technology economic indicators.
From the view of vertical section, there are 2 kinds of round ingot mold. One is with hot-top or firewall, bigger upper and smaller lower. The other one is bottleneck with smaller lower and bigger upper. The former one is used to pour killed steel and is customarily called killed steel ingot mold and is also used to pour boiling steel. The latter one is traditionally used to pour boiling steel, customarily called boiling steel ingot mold, now is also widely used to pour killed steel.
From the view of lumen cross section, the round ingot mold can be square, rectangle, round, polygon and so on. From the view of inwall shape, square ingot mold can be convex side, concave side, straight shape, corrugated side and so on.
PhotoPhotoPhoto
2016-06-22
3 Photos - View album
Add a comment...
Wait while more posts are being loaded