Profile cover photo
Profile photo
David Clunie
Yes, THAT, David Clunie!
Yes, THAT, David Clunie!
About
David's posts

Post has shared content
HA!

Post has attachment

Post has shared content
So yah I think it turns out that the ribbing/banding might have been due to the number of pillars I had on the #trinus or possible a powerful fan blowing in such a way, but additional tests with only one pillar and various settings changed yielded nothing of value or sorts except a whole lot of organizers! :D So I needed to stop printing them and put them to use! :D #3d, #3dmodeling, #colorfabb, #filament, #kickstarter, #make, #organizer, #PLA, #polymakr #translucent, #printer, #printing, #thingiverse, #trinus, #trinus3d

Post has shared content
Just a quick update, which TL; DR didn't really find a solution but did end up with a bunch of orgainzers! :D #3d, #3dmodeling, #colorfabb, #filament, #kickstarter, #make, #organizer, #PLA, #polymakr #translucent, #printer, #printing, #thingiverse, #trinus, #trinus3d
So yah I think it turns out that the ribbing/banding might have been due to the number of pillars I had on the #trinus or possible a powerful fan blowing in such a way, but additional tests with only one pillar and various settings changed yielded nothing of value or sorts except a whole lot of organizers! :D So I needed to stop printing them and put them to use! :D #3d, #3dmodeling, #colorfabb, #filament, #kickstarter, #make, #organizer, #PLA, #polymakr #translucent, #printer, #printing, #thingiverse, #trinus, #trinus3d

Post has attachment
So yah I think it turns out that the ribbing/banding might have been due to the number of pillars I had on the #trinus or possible a powerful fan blowing in such a way, but additional tests with only one pillar and various settings changed yielded nothing of value or sorts except a whole lot of organizers! :D So I needed to stop printing them and put them to use! :D #3d, #3dmodeling, #colorfabb, #filament, #kickstarter, #make, #organizer, #PLA, #polymakr #translucent, #printer, #printing, #thingiverse, #trinus, #trinus3d

Post has attachment
3D Printing : Trinus3d Printer from Kickstarter Odd behaviors? - Part 2
So after a few more experiments with turning on/off smart infill, going from 300 microns back to 150 microns, and even speeding up/slowing down the print speed, I can only get that ribbed pattern to appear on the one print where I'm printing nine pillars al...

Post has attachment

Post has attachment
3D Printing : Trinus3d Printer from Kickstarter Odd behaviors For Certain Prints?
All sliced in their software Pango - So I have a couple of prints that I was doing I derived from http://www.thingiverse.com/thing:961176 . I printed the initial hive file (or a remix actually that just added windows to the back to snake your cable through...

Post has shared content
Thoughts Suggestions appreciated! :D #trinus3d issues i'm currently having with only certain prints... #3dprinting #pla #3d #thingiverse #printing 
www.dbclunie.com - So I have a couple of prints that I was doing I derived from http://www.thingiverse.com/thing:961176 . I printed the initial hive file (or a remix actually that just added windows to the back to snake your cable through) and with the initial print I kept getting this terrible banding along the z-axis which I thought might be z-wobble but it seems a bit too "wide" to be so, so I'm not sure exactly what this is or how to fix it or what causes it.

1st & 2nd images

If you run your finger along the walls you can feel the bumps so its not just within the print. could this be a result of some kind of weird infill (which i think i had set to 20% but as you can tell the walls are thin enough where it doesn't do any infil.

I think created a completely separate file and model (just a single hex pillar and then was going just glue them together in any config I wanted) but was still seeing the banding despite not using any bit of the other file as you can see here...

3rd & 4th Images

then just to check to see if there is an issue with the printer I did a benchy after printing out the single hex pillar and the benchy came out practically perfect. So again i'm not sure what those bands are...

5th and 6th Images (tugboats done right after single hex pillar)

I think the only diff in settings is that the banding hive/pillar is 300 microns vs 150 microns of the benchy or whatever pangos initial slicing is...

any ideas, suggestions, or if others have seen this behavior, any info would be helpful. The hive cable storage is still very much useable and the banding doesn't really effect the projects i'm currently doing just don't want it effect the quality of project later that might rely on perfect finishes and or accuracy...

thanks in advance!
-dbclunie
#3dprinting #trinus3dprinter #trinus #trinus3d #3d #printing #thingiverse #cableorganizer #geek #nerd #pla

PhotoPhotoPhotoPhotoPhoto
2/2/17
6 Photos - View album
Wait while more posts are being loaded